Moottoriohjaimet

Valmistajat

DC MOOTTORIOHJAIN 10A 5V-30V 2CH Näytä suurempana

Cytron DC MOOTTORIOHJAIN 10A 5V-30V 2CH

MOT MDD10A

17 kappaletta

Varastossa

Valmistajan kotisivu

39,93 €

Cytron MDD10A - 10Amp 5V-30V DC-moottorin ohjainkortti, 2 kanavaa

Huom! Sähkönsyötössä (riviliittimen B+ ja B- terminaalit) ei ole polariteettisuojaa!

Cytron MDD10A is the dual-channel version of Cytron MD10C which is designed to drive 2 brushed DC motors with high current up to 10A continuously. Like MD10C, MDD10A also supports locked-antiphase and sign-magnitude PWM signal. It uses full solid state components that offers faster response time and eliminates the wear and tear of the mechanical relay.

It can supports Vmotor from 5V to 30VDC. With the presoldered terminals, and on-board manual/test buttons, you can get started even without any microcontroller. Check the video out:

Nonetheless, it is compatible with Arduino or any microcontroller that can output logic signal at 3.3V or 5.0V, and that includes Arduino Zero and Arduino Micro. And not to forget the famous Raspberry Pi SBC too.

Read User's Review: https://www.robotshop.com/eu/en/cytron-10a-5-30v-dual-channel-dc-motor-driver.html#reviewBox

Which motor is good to be driven by MDD10A? As long as the motor:

  • Is DC Brush motor (Two Terminals)
  • Operating voltage from 5V to 30V
  • Rated Current ≤ 10A
  • Peak Current ≤ 30A

Features

  • Bi-directional control for two brushed DC motors.
  • Support motor voltage ranges from 5V to 30VDC (Rev2.0).
  • No Reverse Polarity Protection at Vmotor, please double check the polarity before power up.
  • Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
  • Support 3.3V and 5V logic level input (for PWM and DIR), compatible with Arduino and Raspberry Pi.
  • Solid state components provide faster response time and eliminate the wear and tear of mechanical relay.
  • Full NMOS H-Bridge for better efficiency and no heat sink is required.
  • Regenerative Braking.
  • Speed control PWM frequency up to 20KHz (output frequancy is same and input frequancy).
  • Support both Locked-Antiphase and Sign-Magnitude PWM operation. ** Note this is not "RC PWM"
  • 2 activation buttons for manual activation or fast test on each channel.
  • Dimension: 84.5mm x 62mm

Document

Tutorials

Packing List

  • 1 x MDD10A Rev2.0
  • 1 x 2510 PCB connector - 5 ways female
  • 5 x 2510 terminal pin

Specifications

Operating Condition
Motor Channel2
Operating Voltage (VDC)5 to 25 (Rev 1.0) 5 to 30 (Rev 2.0)
Peak Current (A)30 (10 seconds)
Continuous Current (A)10
Operating Modes
Arduino ShieldNo- can be used with Wire connection
PWM (Lock-Antiphase and Sign-Magnitude)Yes
UARTNO
AnalogNo
RC Servo SignalNO
Special Protection
Polarity ProtectionNO
Appearance
LEDs IndicatorYes
Test/Manual ButtonYes
Cooling FanNO
Other Features
othersNo heat sink is required

Videos

Klikkaa tarkemmat tiedot
ValmistajaCytron
Valmistajan malliMDD10A
Mitat84,5 x 62 mm
Kanavat2
Jänniteluokka30V
Virtaluokka10A

Tätä tuotetta ostaneet ostivat myös:

 
Tuo ostoskori Excel-tiedostosta (.xls) jossa on tuotekoodit ja määrät